Cart: 0 item (s) - $0.00

Chevrolet Equinox Passenger Airbag Seat Occupancy sensor emulator bypass

Chevrolet Equinox Passenger Airbag Seat Occupancy sensor emulator bypass
Chevrolet Equinox Passenger Airbag Seat Occupancy sensor emulator bypass
Chevrolet Equinox Passenger Airbag Seat Occupancy sensor emulator bypass
Equinox 2007-2010 4 wire sensor
Product Condition: New
$89.00 $99.00
You Will Earn 89 points which is the equivalent of $13.35

Chevrolet Equinox  2007-2010  Front  Passenger Seat Airbag Seat Occupancy Sensor Emulator / Bypass

 
 

    
   C o m p a t i b i l i t y .
MakeChevrolet  USA 
ModelEquinox 
Year : 2007-2010
 
          Prior to order please  check an emulator for equinox 2009-2014 it has the different sensor that was also fitted in Equinox from 2009 to 2014.
   * A D D I T I O N A L    D E T A I L *
Connector  for the sensor  is always attached to the base of the seat  -  picture below.   IS NOT  COMING OF THE FLOOR. 


Sensor side  connector  has  4 wires - red, brown, yellow and white. 
If you are unsure about compatibility with your vehicle, please  send an email to info@airbag360.com    


 

W h a t    a r e   o c c u p a n c y  s e n s o r s  ( O C S ) ?

                   


OCS are very expensive   sensors integrated in vehicle seats . 
Inside the seat, you will find a pressure sensor, and an electronic control unit (ECU). 

When someone sits on the seat, the pressure/ occupancy  sensor signals the occupant's weight to the ECU. 

The ECU then sends that data to the airbag, which has its own control unit. 

Based on that information, the vehicle's computer turns the passenger airbag ON or OFF .


 


So  H o w   A i r b a g  3 6 0   w o r k s  ?


Airbag360 emulators connected in to harness under to passenger seat 
stimulates presence of the passenger.

For Safety reasons Airbag360 emulator generated and send the same signal to ECU as occupied seat.
 
In case of accident  the Airbag will deploy even without presence of Passenger 
Airbag's are permanently activated

 
We Advice that rear-facing child seat's not to be transported on front seat in your vehicle  when emulator is in use.

Remember  even on cars equipped with an OCS, it's always safest to keep small children in the back seat.

Installation of Airbag360 emulator do not required removal  or  and disassemble of the seat  -  NO  labour cost .          


Prior to buying an Airbag360 module, please make sure that your car’s airbag problem has been correctly diagnosed.

If you are unsure about the OBDII diagnostic codes or their description, please contact us and we will check and confirm them for you.

Our Airbag360 emulator will only cure / resolve diagnostic fault codes that indicate a passenger occupancy sensor malfunction.

Any other unrelated codes need to be resolved separately.


I n s t a l l a t i o n 
  

Airbag360 emulators are equipped with an original manufacturer connector.

Installation can be completed in 3 simple steps.

1. With the ignition turned OFF (disconnecting the battery is not necessary) look under the passenger seat and disconnect the original occupancy sensor connector. (3-pronged)

2. Replace the original sensor plug with the Airbag360 emulator

3. Turn on the ignition and start the vehicle.

In most cases after the installation of our emulator, the SRS warning light will go OFF without having to erase any fault codes.

In some cases it depends on how long the malfunction fault code has been stored and in which memory it was saved to.

15952128, 25954278

D E L I V E R Y 

All orders placed with the Airbag360 online shop are processed and posted on the same or next working day.

Estimated delivery time to the U.S is between 7 and 10  working days.

Delivery is made by the USPS by registered mail with tracking number requiring a signature upon receipt.

Write an online review and share your thoughts with other shoppers!

Be the first to review this product