Product information
Model: Enclave
Connector - GM has buried it under the front edge with plastic trim and the seat covering it from vision. See attached pic. Around the bottom 1/3 of the pic you can see a bit of purple, that's the connector, it's attached to the black plastic rail. To get to it, pull back the grey plastic trim, release the leather cover hold down clips and pull the seat cushion back to expose the connector as shown in pic.
Before ordering, visually check under the passenger seat
Look for female side connector - 6 pin with 4 wires - white , yellow , brown, red .
If you are unsure about compatibility with your vehicle, please send us e-mail to info@airbag360.com
OCS are very expensive sensors integrated in vehicle seats .
Inside the seat, you will find a pressure sensor, and an electronic control unit (ECU).
When someone sits on the seat, the pressure/ occupancy sensor signals the occupant's weight to the ECU.
The ECU then sends that data to the airbag, which has its own control unit.
Based on that information, the vehicle's computer turns the passenger airbag ON or OFF .
Airbag360 emulators connected in to harness under to passenger seat
stimulates presence of the passenger.
For Safety reasons Airbag360 emulator generated and send the same signal to ECU as occupied seat.
In case of accident the Airbag will deploy even without presence of Passenger
Airbag's are permanently activated
We Advice that rear-facing child seat's not to be transported on front seat in your vehicle when emulator is in use.
Remember even on cars equipped with an OCS, it's always safest to keep small children in the back seat.
Installation of Airbag360 emulator do not required removal or and disassemble of the seat - NO labour cost .
Prior to buying an Airbag360 module, please make sure that your car’s airbag problem has been correctly diagnosed.
If you are unsure about the OBDII diagnostic codes or their description, please contact us and we will check and confirm them for you.
Our Airbag360 emulator will only cure / resolve diagnostic fault codes that indicate a passenger occupancy sensor malfunction.
Any other unrelated codes need to be resolved separately.
Airbag360 emulators are equipped with an original manufacturer connector.
Installation can be completed in 3 simple steps.
1. With the ignition turned OFF (disconnecting the battery is not necessary) look under the passenger seat and disconnect the original occupancy sensor connector. (3-pronged)
2. Replace the original sensor plug with the Airbag360 emulator
3. Turn on the ignition and start the vehicle.
In most cases after the installation of our emulator, the SRS warning light will go OFF without having to erase any fault codes.
In some cases it depends on how long the malfunction fault code has been stored and in which memory it was saved to.
15952128, 25954278
All orders placed with the Airbag360 online shop are processed and posted on the same or next working day.
Estimated delivery time to the U.S is between 4 and 10 working days.
Delivery is made by the USPS by registered mail with tracking number requiring a signature upon receipt.
Technical specifications
SKU | gm-1 |
MPN | 20933923 |
Brand | AIRBAG360 |
Condition | New |
Product Code | Gm1 |
Customer reviews
So far so good
After several intermittent "service airbag" warnings followed by a steady warning I took my 2008 Enclave to my mechanic for diagnosis. A bad sensor and a projected repair estimate between $1200-1500 I elected not to do the repair as it is simply a spare car. Researching online I came across Airbag 360 and decided it was worth the $100 investment. It arrived but had no instructions and that is why I deducted 1 star. The only visible wiring connector with the seat installed has at least 8 wires. You need to unbolt the seat so that you can lay it back to gain access to the underside. The connector then was obvious and the installation took all of 5 minutes. Prior to reinstalling the seat I started the car to see if it worked. "airbag on" light is on and the passenger "seatbelt" light on because the car thinks the seat is now occupied. Fastened the belt and all indications now normal. YouTube has a video of how to uninstall the seat if you're not sure how to do it. Hopefully this will be a permanent fix.
Haynes Dunn | TEXAS CITY, TX | April 2020